Browsing this Thread:
1 Anonymous Users
|
Re: Ethernet AC320004-7 KSZ8863 Daughter Board 使用方法
|
|
新會員

Joined
: 2023/8/10 15:12 最後登入時間
: 2023/9/11 10:48
Group:
註冊會員
Level : 1 HP : 0 / 5 MP : 1 / 24 EXP : 21
|
抱歉,貼錯位置,重新張貼於 類比及介面 謝謝
發表於: 2023/8/10 18:12
|
|
|
Ethernet AC320004-7 KSZ8863 Daughter Board 使用方法
|
|
新會員

Joined
: 2023/8/10 15:12 最後登入時間
: 2023/9/11 10:48
Group:
註冊會員
Level : 1 HP : 0 / 5 MP : 1 / 24 EXP : 21
|
大家好,我在工作上有Ethernet Daisy-Chain的需求,所以買了一個 AC320004-7 KSZ8863晶片 3 Port的Ethernet Kit開發,剛好手邊有ESP32以及網路上有ESP32支援KSZ8863的driver,但是在使用過程中,一直沒有成功,目前無法使用SPI訪問register取得chip id,其他問題如下:
應用:先使用範例程式測試成功,在實作daisy-chain,使用SPI或I2C或SMI
以下問題使用SPI訪問KSZ8863 register,以及外部參考時鐘REFCLKI 問題1:總共需要接幾條線,到AC320004-7上?總共8條,以下的認知是否正確? 1_3V3、2_GND、3_RST(重置)、4_SPI_MOSI、5_SPI_MISO、6_SPI_CLK、7.SPI_SS、8_50Mhz_REF_CLK(外部參考時鐘)
問題2:AC320004-7上有許多DNP的部分,如果想要使用SPI,我的作法是否正確? 依據 KSZ8863 Daughter Board Information Sheet 文件 Page 5 1. 依據SPI Communication Option,將R44及R24各上一個1K的電阻(原為DNP狀態) 2. 依據Bus Communication Configuration,將R29上一個1K的電阻,另一個R28保持DNP狀態,選擇SPI Slave Mode 3. 依據Clock Source Configuration,電路圖顯示R22及R23皆有接地,其值應該都是0,選擇External 50MHz OSC input to SMTXC3/REFCLKI_3 directly and X1 p,外部參考時鐘
以上問題請協助,謝謝 Regards, Ken.
GIGA-TMS INC 集佳股份有限公司 鄭軻忠 KEN MAIL :ken@gigatms.com.tw TEL:02-26954214#549 FAX:02-26954213 地址 : 新北市汐止區康寧街169巷31號9樓之2
發表於: 2023/8/10 16:36
|
|
You can view topic.
你 不可以 發起新主題
You cannot reply to posts.
You cannot edit your posts.
You cannot delete your posts.
You cannot add new polls.
You cannot vote in polls.
You cannot attach files to posts.
You cannot post without approval.
You cannot use topic type.
You cannot use HTML syntax.
You cannot use signature.
You cannot create PDF files.
You cannot get print page.