Re: ICD2 秀出ICD0083: Target not in debug mode, unable to perform operation
|
||||
---|---|---|---|---|
中級會員
|
據說ICD2在燒錄2010時會有問題?要修改ICD2的線路對吧??
http://www.microchip.com.tw/files/icd2_2_wire_short.jpg
發表於: 2004/11/18 12:29
|
|||
|
Re: ICD2 秀出ICD0083: Target not in debug mode, unable to perform operation
|
||||
---|---|---|---|---|
新會員
|
謝謝tony大大的意見
6.電源確定有接.... 7.我昨晚接了16f877來試,功能正常.... 8.我會去研究一下.... 後來又換了一個30f2010來試...還是掛點
發表於: 2004/11/15 8:02
|
|||
|
Re: ICD2 秀出ICD0083: Target not in debug mode, unable to perform operation
|
||||
---|---|---|---|---|
新會員
|
謝謝大大指點...
剛剛小弟拆開來看,發現沒有r25和r36電阻,所以我想我的ICD2應該還蠻新的.. ,唉~~難道是我的icd2壞了嗎?????????還是哪裡有設錯呢??請知道的大大指點一下
發表於: 2004/11/13 14:59
|
|||
|
Re: ICD2 秀出ICD0083: Target not in debug mode, unable to perform operation
|
||||
---|---|---|---|---|
資深會員
|
1. 檢查 6pin 排線,拔下後重新確實插妥。
2. 重新燒錄 MCU (Debugger→Program)。 3. 先降低振盪與工作頻率試看看。 4. 安裝最新版本 MPLAB ,裝好後給 ICD2 Download 最新 firmware。 5. 如果 ICD2 不是最新版本的,請依 Microchip 通告修改線路(針對 dsPIC,沒用到的人可以不改),修改通告見檔案下載→發展工具 http://www.microchip.com.tw/modules/mydownloads/viewcat.php?cid=2 修改很簡單,可以用細銀線直接短路或換 0 ohm 電阻,由於上面都是 SMD 零件,請小心焊接。同時別不小心把旁邊的塑膠插座熔了。 如果你不喜歡直接短路(0 ohm),網路上也有人反映說 20 或 22 ohm 也可以工作。 如果不會改,不必勉強,請送原代理商或 Microchip 處理。
發表於: 2004/11/13 11:39
|
|||
|
Re: ICD2 秀出ICD0083: Target not in debug mode, unable to perform operation
|
||||
---|---|---|---|---|
新會員
|
看到原廠網站Dspicdem 28pin starter demo user's guide,
文件裡頭是使用7.37M oscillator,Oscillator mode----XT w/PLL 4x 就想說照做試試~買了一個比較接近的....7.2M,但還是結果一樣....
發表於: 2004/11/13 8:32
|
|||
|
Re: ICD2 秀出ICD0083: Target not in debug mode, unable to perform operation
|
||||
---|---|---|---|---|
高級會員
|
我的經驗是..Oscillator 沒有起振...
量一下晶體的輸出吧.. Oscillator Mode 應該是要設成HS... Try Try 看吧..僅供參考.. 因為我是用PIC16系列的經驗來判斷的... CC
發表於: 2004/11/13 0:29
|
|||
|
ICD2 秀出ICD0083: Target not in debug mode, unable to perform operation
|
||||
---|---|---|---|---|
新會員
|
各位大大好:
我現在用ICD2 debug 30f2010,秀出以下訊息... Setting Vdd source to MPLAB ICD 2 Target Device dsPIC30F2010 found, revision = mm3 a0 ...Reading ICD Product ID Running ICD Self Test ...Passed ...Download Operating System Succeeded MPLAB ICD 2 Ready Resetting Target MPLAB ICD 2 Ready ICDWarn0015: Program memory has changed since last program operation? Continue with Debug operation? Stepping Target ICD0083: Target not in debug mode, unable to perform operation MPLAB ICD 2 Ready Running ICD Self Test ...Passed 看了一些user guide後~想說是我的Configuration Bits設定有問題 我把 1.Clock switching and monitor---disable 2.Oscillator mode----primary oscillator 3.Oscillator mode----XT 硬體 1.一個20M Oscillator接在osc1和osc2並且接兩個20p電容接地 2.emuc和emud接了 3.nmclr接電阻再接vdd,電阻用過4.7k,10k,22k都不行 找了好久找不到問題........
發表於: 2004/11/12 23:32
|
|||
|