請問MPlab IDE7.0的問題
|
||||
---|---|---|---|---|
初級會員
|
請問版主:
小弟在使用MPlab IDE7.0時,不論在軟體模擬或是接上ICD2實測時,按下暫停icon後要再繼續跑時,IDE7.0就會要求我重新compiler一次,很不方便,尤其是還要重燒錄,所以不知您是否有遇到相同的問題?謝謝
發表於: 2005/3/18 21:29
|
|||
|
Re: 當我用mcc compiler 後要怎麼燒在其他的燒錄器呢?
|
||||
---|---|---|---|---|
資深會員
|
你編譯完後有個.hex的檔案
把那個燒錄進去就可以 我以前試過 用MPLAB編譯完成 再把那個檔案用ALL11燒錄進IC就可執行
發表於: 2005/3/18 15:56
|
|||
|
當我用mcc compiler 後要怎麼燒在其他的燒錄器呢?
|
||||
---|---|---|---|---|
新會員
|
當我用C將程式寫完後 compiler也沒有問題,要怎麼燒在其他的燒錄器呢?我有一台all-11的燒錄器,可以用這台燒嗎?
發表於: 2005/3/18 15:39
|
|||
|
Re: CAN system's problem with 3 nodes
|
||||
---|---|---|---|---|
版主
|
if ( CANIsRxReady( ) )
{ CANReceiveMessage (&RX_ID1.Slave_ID1,RX_Data_Buf1,&RX_Data_Len1,&RX_Message_Flag) ; : : } Please add the CANIsRxReady( ) for checking the CAN receiver message polling.
發表於: 2005/3/18 13:55
|
|||
|
Re: CAN system's problem with 3 nodes
|
||||
---|---|---|---|---|
初級會員
|
Anymore,neither node1 nor node2 can receive the message with ID 0X220 from node3,and node1 to node3 usually reset much times when start,then they can work for a little long time.why?
發表於: 2005/3/18 13:23
|
|||
|
Re: AD转换问题
|
||||
---|---|---|---|---|
初級會員
|
谢谢!问题已解决,问题的关键确实是因为通道切换后需要适当的延时。
發表於: 2005/3/18 13:19
|
|||
|
Re: CAN system's problem with 3 nodes
|
||||
---|---|---|---|---|
初級會員
|
No,node3 does nothing but waits to receive the message,I think busy is unreasonable .
發表於: 2005/3/18 13:16
|
|||
|
Re: CAN system's problem with 3 nodes
|
||||
---|---|---|---|---|
資深會員
|
我猜你的 node3 太忙碌了,以致於來不及去收 buffer上的資料
發表於: 2005/3/18 11:43
|
|||
|
Re: 有關LIN Bus的問題...
|
||||
---|---|---|---|---|
資深會員
|
*** * 012345 * *** 一、錯一bit,隨便檢查都會發現 二、錯兩bit,除02 35兩種組合之外,其餘全能發現 三、錯3bit,全能發現 四、錯4bit,全能發現(02 35同時出包除外) 五、再錯下去就沒有意思了 總結: 除了 02 or 35 or 0235這三種錯誤組合,系統會無法檢測之外,其它的錯誤都能發現。 又,錯誤基本上會連續發生,不容易發生,一個錯,下一個對,下一個又錯,這樣的組合。
發表於: 2005/3/18 11:39
|
|||
|